DC motor driver
Showing all 40 results
-
Best Prices, Stepper Motor Drivers
TB6600 Stepper Motor Driver Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axis
Best Prices, Stepper Motor DriversTB6600 Stepper Motor Driver Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axis
SKU:- Input Current: 0~5A
- Output Current: 0.5~4.0A
- Control Signal: 3.3~24V
- Power (MAX): 160W
- Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32
- Temperature: -10～45℃
- H bridge bipolar constant current drive.
SKU: n/a -
-
Relay Modules
5-36v Switch Drive High-power MOSFET Trigger Module
SKU:This 5-36v Switch Drive High-power MOSFET Trigger Module can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps,  solenoid valves, PWM, motor speed control, lamp brightness. etc.
SKU: n/a -
Best Prices, Servo Motor Drivers
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
Best Prices, Servo Motor Drivers16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
SKU:- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: n/a -
Breakout Board
IRF520 MOSFET Driver Module for Arduino ARM Raspberry pi
SKU:- Voltage: 3.3 – 5V.
- Ports: Digital Level.
- Output load voltage: 0-24 V.
- Output load current: <5A (1A above need to add heat sink).
- Platform: Arduino, MCU, ARM, raspberry pi.
- Using original IRF520 Power MOS, you can adjust the output PWM
SKU: n/a -
Cytron Motor Drivers
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
SKU:- Bi-directional control for 1 brushed DC motor, single channel
- Support motor voltage ranges from  5V to 30V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Cytron Motor Drivers
Cytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
SKU:- Bi-directional control of 2 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Stepper Motor Drivers
L298N Dual H Bridge DC/Stepper Motor Driver Controller Module
SKU:- Driver chip: L298N Dual H Bridge
- Supply voltage: VMS 5V – 35V
- Peak current IO: 2A per bridge
- Max power consumption: 20W
- Provides 4 LEDs that reflect the state of the control logic
- Independent direction, speed, and braking for each motor
SKU: n/a -
Brushed / Brushless DC motor Driver
20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
Brushed / Brushless DC motor Driver20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
SKU:- Adjustable speed range: 0%-100%.
- Speed adjustment way: Potentiometer.
- Output voltage: Linear under load.
- Speed control type: Basins.
- Output voltage: Load Linear
- Type: Adjusting flow
- The motor running condition adjustment: Forward  / Stop / Reverse
SKU: n/a -
Cytron Motor Drivers
MD13S 13Amp DC Motor Driver – GROVE Compatible
SKU:-
Support motor voltage ranges from 6V to 30V
-
Maximum current up to 13A continuous and 30A peak (10 seconds).
-
GROVE compatible
-
3.3V and 5V logic level input.
-
SMD compatible
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 1
- No. of Channels: 1
SKU: n/a -
-
Cytron Motor Drivers
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
SKU:- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 30V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Stepper Motor Drivers
TB6600 Stepper Motor Driver Controller 8~50V 4.5A
SKU:- Supply Voltage: 8V – 50V DC (36V recommended).
- Output current: 0.3A – 4.5A (peak value of 5A).
- Micro Step: 1, 2, 8, 16.
- Maximum PWM frequency:Â 200kHz.
- Adjustments for the maximum current of the LED: 1A, 2.2A, 3.3A, 4.5A.
- Operating temperature: -10 to + 45 ° С.
SKU: n/a -
Brushed / Brushless DC motor Driver
Monster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)
SKU:- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 34 mΩ
- Maximum PWM frequency: 10 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
SKU: n/a -
Brushed / Brushless DC motor Driver
Dual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A)
Brushed / Brushless DC motor DriverDual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A)
SKU:- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 19 mΩ (per leg)
- Maximum PWM frequency: 20 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
SKU: n/a -
Cytron Motor Drivers
Cytron Smart Drive Mdds30 Dual 30A (80A Peak)
SKU:- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm.
SKU: n/a -
Cytron Motor Drivers
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
SKU:Â
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
SKU: n/a -
-
Dimension Engineering Motor Drivers
Sabertooth Dual 12A Motor Driver
SKU:- 12A continuous, 25A peak per channel Up to 24V in
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Peak Current (A): 25A
- Continuous Current (A): 12
- Operating Voltage(VDC): 18 to 24V
- No. of Channels: 2
SKU: n/a -
Cytron Motor Drivers
Cytron 25A 7V-58V DC motor driver with Switch and Potentiometer Control (MD25HV POT)
Cytron Motor DriversCytron 25A 7V-58V DC motor driver with Switch and Potentiometer Control (MD25HV POT)
SKU:- Bidirectional control for one brushed DC motor.
- Maximum Motor Current: 25A continuous, 60A peak.
- 5V output for the host controller (250mA max).
- Buttons for quick testing.
- PWM frequency up to 40kHz.
- Dual Input Mode: PWM/DIR or Potentiometer/Switch Input.
SKU: n/a -
Dimension Engineering Motor Drivers
Sabertooth Dual 25A Motor Driver
SKU:- 25A continuous, 50A peak per channel
6-30V nominal, 33.6V absolute maximum - Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Input modes: Analog, R/C, simplified serial, packetized serial
SKU: n/a - 25A continuous, 50A peak per channel
-
Cytron Motor Drivers
Cytron 10Amp 7V-30V DC Motor Driver for R/C (2 Channel) MDDRC10
SKU:- Operating Voltage: DC 7 V to 30 V
- Maximum Motor Current: 10 A continuous, 30 A peak
- Motor Output PWM Frequency: 20 kHz
- RC Input Voltage (RC1 & RC2): Low Level: 0-0.7 V | High Level: 1.5-15 V
- Output Maximum Current: 0-500 mA
SKU: n/a -
Dimension Engineering Motor Drivers
Sabertooth Dual 32A Motor Driver
SKU:- 32A continuous, 64A peak per channel
- 6-30V nominal, 33.6V absolute maximum
- Synchronous regenerative drive
- Ultrasonic 30 kHz switching frequency
- Thermal and overcurrent protection
- Battery protection mode
- USB control and monitoring
- USB serial converter mode for Kangaroo x2
- Configurable current limiting
- Custom user modes
- 12-bit motor outputs
SKU: n/a -
Refurbished, Refurbished & Partial Working, Refurbished Motors | Drivers | Pumps | Actuators
Refurbished – Sabertooth Dual 25A Motor Driver
Refurbished, Refurbished & Partial Working, Refurbished Motors | Drivers | Pumps | ActuatorsRefurbished – Sabertooth Dual 25A Motor Driver
SKU:- 25A continuous, 50A peak per channel
6-30V nominal, 33.6V absolute maximum - Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Input modes: Analog, R/C, simplified serial, packetized serial
SKU: n/a - 25A continuous, 50A peak per channel
-
-
Cytron Motor Drivers
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
SKU:-
Input Voltage (Motor): 10 – 45VDC
- Maximum current up to 100A peak (1 second), 60A continuously, each channel.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
- DC Brush motor Driver, not for brushless motor
- Dual Channels, it can drive two brush motor independently, or mixed.
- Version: Rev 1.10
SKU: n/a -
-
Cytron Motor Drivers
Cytron 2Amp Motor Driver Shield
SKU:-
Logic control, 5V from Arduino main board
-
Polarity protection for External motor power input
-
2 fast test buttons for each motor channel
-
Motor Driven Voltage：6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source)
-
Up to 2A current each channel
-
Pin 4, 5,6,7 are used to drive two DC motor
-
Support PWM speed control
-
Support advance speed control
SKU: n/a -
-
-
-
Cytron Motor Drivers
Cytron FD04A 4-Channel Motor Driver
SKU:- Industrial grade PCB.
- Vmotor: 7 V to 25 V DC.
- Each component is soldered properly and tested.
- Able to drive 4 DC motor at 2.5A (peak), 1.5A continuously.
- 2 LEDs as a direction indicator for each motor.
- 1 LED as a power indicator.
- A pluggable connector for more user-friendly design.
- Fully compatible with Cytron DIY project, Flexibot – Using Transwheel (PR19).
SKU: n/a -
Cytron Motor Drivers
Cytron Dual channel 10A Motor Driver UNO Robot Controller
SKU:- Onboard 1A (maximum) 5V voltage regulator.
- Onboard 500mA (maximum) 3.3V voltage regulator.
- 0-5V digital outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
- 6 Analog Inputs (Can be digital I/O too).
- Maximum current up to 10A continuous and 30A Peak.
- ISP 6-pin Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- R3 Shield Compatible.
SKU: n/a -
Cytron Motor Drivers
Cytron Driver HAT-MDD10
SKU:- Support motor voltage ranges from 6VDC to 24VDC.
- Onboard the test button for manual control of the motor.
- Every channel output built with LED indicator.
- Current limiting at 30A.
- Operating Voltage(VDC): 6 to 24
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 10
- No. of Channels: 2
- Operating Modes: PWM (Lock-Antiphase and Sign-Magnitude): Yes, UART: No, Analog:No, RC Servo Signal: No
SKU: n/a -
Dimension Engineering Motor Drivers
Sabertooth Dual 5A Motor Driver for R/C
SKU:- Operating Voltage(VDC): 6-18
- Peak Current (A): 10
- Continuous Current (A): 5
- No. of Channels: 2
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode-compatible with: 6-12 cell NiMH or NiCd, 2s-4s LiPo, 6V or 12V lead acid (not 18+V lead acid!)
SKU: n/a -
Cytron Motor Drivers
Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)
SKU:- Bi-directional control for a single brushed DC motor.
- Support input voltage from 8V to 28V.
- Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
- 16 KHz switching frequency for quiet operation.
- LiPo battery low voltage warning.
- Thermal protection.
SKU: n/a -
Brushed / Brushless DC motor Driver
Sabertooth Dual 5A Motor Driver
SKU:- Input Voltage: 6V to 18V
- Compatible with: 6-12 cell NiMH or NiCd, 2s-4s LiPo
- 5A continuous per channel, 10A peak
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
SKU: n/a -
Brushed / Brushless DC motor Driver
Cytron Smartdrive40 40Amp Dc Motor Driver (Peak 80Amp) Mds40A
SKU:- Bi-directional control for a single brushed DC motor.
- Support motor from 7V to 25V.
- Maximum current up to 80A peak (1 second), 40A (5 minutes) or 30A (> 20 minutes) continuously.
- 16 KHz switching frequency for quiet operation.
- Reverse polarity protection.
- LiPo battery low voltage warning.
- Thermal protection.
- Current limiting base on temperature.
SKU: n/a