Cytron
Showing all 37 results
-
Cytron Motor Drivers
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
SKU: 2777- Bi-directional control for 1 brushed DC motor, single channel
- Support motor voltage ranges from  5V to 30V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: 2777 -
Cytron Motor Drivers
Cytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
SKU: 3405- Bi-directional control of 2 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: 3405 -
Cytron Motor Drivers
MD13S 13Amp DC Motor Driver – GROVE Compatible
SKU: 24027-
Support motor voltage ranges from 6V to 30V
-
Maximum current up to 13A continuous and 30A peak (10 seconds).
-
GROVE compatible
-
3.3V and 5V logic level input.
-
SMD compatible
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 1
- No. of Channels: 1
SKU: 24027 -
-
Cytron Motor Drivers
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
SKU: 2774- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 30V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: 2774 -
Cytron Motor Drivers
Advanced Auto-Calibrating Line Sensor LSA08
SKU: 6182- 8 sensor pairs spaced 16mm.
- 12V input power
- Onboard Mode and a Select button for instant configuration of LSA08
- LCD display unit showing 8 sensors analog value with bar chart and line position.
- Simple Auto-Calibration function to the line following surface.
- Low current consumption (typically 26mA)
- Works on glossy or reflective surface
- Refresh rate up to 200Hz.
SKU: 6182 -
Cytron Motor Drivers
Cytron Smart Drive Mdds30 Dual 30A (80A Peak)
SKU: 29672- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm.
SKU: 29672 -
-
-
-
Cytron Motor Drivers
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
SKU: 4565Â
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
SKU: 4565 -
-
-
-
-
Cytron Motor Drivers
Enhanced Cytron 40Amp DC Motor Driver (Peak 80amp) MDS40B
SKU: 11648-
Bi-directional control for a single brushed DC motor.
-
Support motor from 10V to 45V.
-
Maximum current up to 80A peak, reduce to 40A gradually according to temperature.
-
16 KHz switching frequency for quiet operation.
-
NO Reverse polarity protection.
-
Protection of overvoltage.
SKU: 11648 -
-
-
Cytron Motor Drivers
10A Motor Driver Shield – MD10
SKU: 3408- Bi-directional control of 1 brushed DC motor.
- Support motor voltage ranges from 7V to 25V, .
- Maximum current up to 10A continuous and 15A peak (10 seconds).
- Solid state components provide faster response time and eliminate the wear and tear of a mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
- Speed control PWM frequency up to 10KHz.
- Selectable digital pins for PWM and DIR.
SKU: 3408 -
Cytron Motor Drivers
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
SKU: 8014-
Input Voltage (Motor): 10 – 45VDC
- Maximum current up to 100A peak (1 second), 60A continuously, each channel.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
- DC Brush motor Driver, not for brushless motor
- Dual Channels, it can drive two brush motor independently, or mixed.
- Version: Rev 1.10
SKU: 8014 -
-
Cytron Motor Drivers
Cytron 2Amp Motor Driver Shield
SKU: 16014-
Logic control, 5V from Arduino main board
-
Polarity protection for External motor power input
-
2 fast test buttons for each motor channel
-
Motor Driven Voltage：6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source)
-
Up to 2A current each channel
-
Pin 4, 5,6,7 are used to drive two DC motor
-
Support PWM speed control
-
Support advance speed control
SKU: 16014 -
-
Cytron Motor Drivers
Cytron Arduino PS2 Shield
SKU: 2506- 5V powered low current consumption.
- Simple to use UART protocol
- Vibrator motor on PS2 is controllable.
- Wired and Wireless PS2 controller is supported.
- PS2 Controller will automatically operate in analog mode.
- A status LED
- Jumper selector to select different UART Baud Rate (9600, 57600, 115200).
- Jumper selectors to select different digital pin as UART TX and RX pin.
SKU: 2506 -
Cytron Motor Drivers
Cytron FD04A 4-Channel Motor Driver
SKU: 16010- Industrial grade PCB.
- Vmotor: 7 V to 25 V DC.
- Each component is soldered properly and tested.
- Able to drive 4 DC motor at 2.5A (peak), 1.5A continuously.
- 2 LEDs as a direction indicator for each motor.
- 1 LED as a power indicator.
- A pluggable connector for more user-friendly design.
- Fully compatible with Cytron DIY project, Flexibot – Using Transwheel (PR19).
SKU: 16010 -
Cytron Motor Drivers
Cytron ESP8266 WiFi Shield V2.0 W/ Micro SD Card Slot For Arduino Uno
SKU: 43298- Basically, Rev2.0 utilize WROOM-02 instead of ESP8266-12 as the WiFi module.
- Separate 3.3V voltage regulator for ESP8266-12 WROOM-02 module, 500mA max output.
- Each and every board is preassembled and tested before it is being shipped out to you.
- 802.11 b/g/n.
- Support Wi-Fi Direct (P2P), soft-AP.
- Integrated TCP/IP protocol stack.
SKU: 43298 -
PIC Development board
Cytron 40 pins PIC Start-Up Kit SK40C
SKU: 10095-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
Operating Voltage Range: 7V – 15VDC
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
-
UART connection to interface with other controller or even computer.
SKU: 10095 -
-
Cytron Motor Drivers
Cytron Dual channel 10A Motor Driver UNO Robot Controller
SKU: 49866- Onboard 1A (maximum) 5V voltage regulator.
- Onboard 500mA (maximum) 3.3V voltage regulator.
- 0-5V digital outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
- 6 Analog Inputs (Can be digital I/O too).
- Maximum current up to 10A continuous and 30A Peak.
- ISP 6-pin Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- R3 Shield Compatible.
SKU: 49866 -
Cytron Motor Drivers
Cytron Driver HAT-MDD10
SKU: 29670- Support motor voltage ranges from 6VDC to 24VDC.
- Onboard the test button for manual control of the motor.
- Every channel output built with LED indicator.
- Current limiting at 30A.
- Operating Voltage(VDC): 6 to 24
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 10
- No. of Channels: 2
- Operating Modes: PWM (Lock-Antiphase and Sign-Magnitude): Yes, UART: No, Analog:No, RC Servo Signal: No
SKU: 29670 -
-
-
Cytron Motor Drivers
Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)
SKU: 2784- Bi-directional control for a single brushed DC motor.
- Support input voltage from 8V to 28V.
- Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
- 16 KHz switching frequency for quiet operation.
- LiPo battery low voltage warning.
- Thermal protection.
SKU: 2784 -
Shield for Arduino
PS2 Controller Starter Kit
SKU: 7438- Stable 5V powered, low current consumption, less than 150mA.
- 1 standard PS2 controller socket.
- Communicate with host microcontroller through 5V TTLÂ UART.
- Simple inquiry command and button status feedback for the host process.
- Vibrator motor is controllable.
- Wired or wireless PS2 controller is fully compatible.
- A small LED as the indicator for communication between SKPS and PS2 controller.
SKU: 7438 -
PIC Programmer
ICSP Universal Socket
SKU: 10061To ease user, Cytron has created this UIC-A so that user can use any programmer regardless of the development board. For example, a development board which uses PICkit2’s socket standard, which is 6-way header pins can be programmed with UIC000B by using the UIC-A!
SKU: 10061 -
Brushed / Brushless DC motor Driver
Cytron Smartdrive40 40Amp Dc Motor Driver (Peak 80Amp) Mds40A
SKU: 2780- Bi-directional control for a single brushed DC motor.
- Support motor from 7V to 25V.
- Maximum current up to 80A peak (1 second), 40A (5 minutes) or 30A (> 20 minutes) continuously.
- 16 KHz switching frequency for quiet operation.
- Reverse polarity protection.
- LiPo battery low voltage warning.
- Thermal protection.
- Current limiting base on temperature.
SKU: 2780 -
PIC Development board
28 Pins PIC Start-up Kit – SK28A
SKU: 10080-
Industrial grade PCB.
-
Every board is being tested before it is shipped out.
-
Compact platform and breadboard-friendly
-
Suitable for hobbyists and expert.
-
Save development and soldering time.
-
Turn pin for crystal comes with 20MHz Crystal by default, the user may use crystal at various frequencies
-
Mini USB socket on board may use PIC18F2550 for USB device development, example USB Bootloader.
-
2×8 Character Parallel LCD pad ready (optional).
SKU: 10080 -
-
Shield for Arduino
Cytron Easy MP3 Shield
SKU: 7982-
Onboard high-quality MP3 decoder.
-
Onboard dual channel/Stereo 3W differential audio amplifier for an external speaker.
- A MicroSD status LED.
-
Onboard stereo 3.5mm audio jack socket for earphones.
-
Onboard microSD socket for MP3 audio files storage.
-
The interface from Arduino, UART, selectable to use soft serial.
-
Stackable side headers.
- Supply voltage: 5V.
SKU: 7982 -
-
PIC Development board
40 pins PIC Start-Up Kit Combo 1 – SK40C PIC16F877A (SK40C1)
SKU: 10097-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
SKU: 10097 -
-
PIC Development board
40 pins PIC Start-Up Kit Combo 2 SK40C + PIC18F4550 (SK40C2)
SKU: 10105-
ICSP connector for UIC00B -simple and fast method to load program.
-
Perfect fit for 40 pins PIC16F and PIC18F.
-
2 x programmable switch.
-
2 x LED indicator.
-
Exchangeable Crystal.
-
Existing pad for 16 x 2 characters LCD display.
-
UART connection to interface with other controller or even computer.
-
USB on board for certain PIC18F.
SKU: 10105 -
-
PIC Development board
40 Pins dsPIC Start-Up Kit – SKDS40A
SKU: 10086-
ICSP connector for UIC00A /B-simple and fast method to load program.
-
Perfectly fit for 40 pins dsPIC (16-bit), NOT for the 40-pins 8-bit PIC.
-
2 x programmable switch.
-
2 x programmable LED indicator.
-
Changeable Crystal – default 10MHz.
-
Existing pad for 16 x 2 characters LCD display.
SKU: 10086 -
-
PIC Development board
18 Pins PIC Start-up Kit – SK18B
SKU: 10064-
Compact, powerful, flexible and robust start-up platform.
-
No extra components required for the PIC to function.
-
No more frustrated work plugging PIC out and back for re-programming.
-
Perfectly fit for 18 pins PIC16F MCU.
-
With UIC00A, the program can be loaded in less than 4 seconds.
-
On/Off switch for main power
-
DC adaptor socket as power input
SKU: 10064 -
-
USB Interface Module
USB PIC Programmer – UP00B
SKU: 10109- USB powered, no extra power needed to load program
- Two ZIF sockets (20 pins and 40 pins) to ease the program loading process
- Support most 8pin, 18pin, 28pin and 40pin PDIP 8 bit PIC MCU
- Support Windows XP, Vista, 7 (32 and 64-bits)
- Support Intel and AMD based system
- Support Laptop and desktop PC
SKU: 10109
