8 Channel Relay
Showing all 10 results
-
Relay Modules
8 Channel Isolated 5V 10A Relay Module opto coupler For Arduino PIC AVR DSP ARM
SKU:- Channel: 8 channel
- Relay Operating Voltage: 5V
- One normally closed contact and one normally open contact
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
SKU: n/a -
Relay Modules
5V 8 Channel Relay Module
SKU:- The 8550 transistor drive, driveability.
- A fixed bolt holes for easy installation.
- It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red)
- Relay control interface by single-chip IO.
- Low-level suction close, high-level release.
- Easy to use, simple 3 line structure.
SKU: n/a -
Relay Modules
8 Channel 5V Solid State Relay Module Board OMRON for Arduino
SKU:- 8-channel 2 AMP Solid State Relay board.
- Control 8 loads of up to 2 amps each at 120 V or 240 VAC.
- Good for lighting, Holiday displays etc.
- With 8 Solid State Relays: 2A at 100 to 240 VAC.(50/60 Hz).
- Power supply: 5 V DC(160 mA)
- Trigger Current: 2mA
- Trigger Voltage: 3.3V-5V
SKU: n/a -
Relay Modules
5V 2A 8-Channel SSR G3MB-202P Solid State Relay Module (Low level Trigger)
SKU:- 8 channel 2 AMP Solid State Relay board
- Control 8 loads of up to 2 amps each at 120V or 240V AC.
- Good for lighting, holiday displays etc.
- Has been assembled, and the electrical test passed.
- Operating Voltage: 5V
- Operating Current: 16mA
- Maximum Load: 2A @ 240VAC
SKU: n/a -
Relay Modules
8 Road/Channel Relay Module (with light coupling) 12V
SKU:- Operating Voltage: 12V DC
- Equipped with high-current relay 10A@250VAC / 10A@30VDC
- It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc
- High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
- Freewheeling diode to protect your microcontroller
- Input Signal Pin connected to Burg stick for easy accessibility
- LED Status indicators to indicate the relay ON/OFF status
- Mounting holes provided
SKU: n/a -
Relay Modules
8 Road/Channel Relay Module (with light coupling) 24V
SKU:- Operating Voltage: 24V DC
- Equipped with high-current relay 10A@250VAC / 10A@30VDC
- It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc
- High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
- Freewheeling diode to protect your microcontroller
- Input Signal Pin connected to Burg stick for easy accessibility
- LED Status indicators to indicate the relay ON/OFF status
- Mounting holes provided
SKU: n/a -
Relay Modules
12V 8 Channel Relay Module
SKU:- Using high-current relay, AC250V 10A DC30V 10A.
- Contact some independent wiring, safe and reliable.
- The standard interface can be extended to a variety of development boards.
- With fixed screw holes for easy installation.
- Suitable for a variety of platforms such as 8051/AVR/AVR/ARM.
SKU: n/a -
USB Interface Module
Waveshare Industrial Modbus RTU 8-Channel Relay Module RS485 Bus, Multi Protection (Without Power Adapter)
USB Interface ModuleWaveshare Industrial Modbus RTU 8-Channel Relay Module RS485 Bus, Multi Protection (Without Power Adapter)
SKU:- Power supply voltage: 5V
- Communication interface: RS485
- Relay channels: 8
- Contact form: 1NO 1NC
- RS485 address: 1~255
- Communication protocol: Standard Modbus RTU protocol
SKU: n/a -