Shield for Arduino
Showing 49–67 of 67 results
-
Shield for Arduino
Arduino Nano PRATHAM 1.0 Development Board
SKU:- On-board ON/OFF switch and power LED
- Onboard Voltage Regulator for stable power supply
- Arduino Nano compatible (direct plug-in for Arduino Nano board)
- On-board direct plug-in for 16X2 Liquid Crystal Display with contrast adjustment
- On-board L293D Motor Driver chipset
- I2C communication pins available for IMU Sensor
- Pin header to connect Line Follower Sensor (up to an array of 6) with power pins
SKU: n/a -
Shield for Arduino
Colorduino LED RGB Dot Matrix Driver Board with 5mm 8*8 RGB LED for Arduino
SKU:- 8bits colors support with 6bits correction for each color in every dots
- Hardware 16MHz PWM support
- 24 constant current channels of 100mA each
- Current Consumption(Except LED matrix): 20mA typical (40mA maximum)
- Drive current(Every channel):Â 500mA
- Drive current(Every dot) :Â 58mA
SKU: n/a -
Shield for Arduino
Cytron Easy MP3 Shield
SKU:-
Onboard high-quality MP3 decoder.
-
Onboard dual channel/Stereo 3W differential audio amplifier for an external speaker.
- A MicroSD status LED.
-
Onboard stereo 3.5mm audio jack socket for earphones.
-
Onboard microSD socket for MP3 audio files storage.
-
The interface from Arduino, UART, selectable to use soft serial.
-
Stackable side headers.
- Supply voltage: 5V.
SKU: n/a -
-
-
Shield for Arduino
Ethernet W5100 R3 Ethernet & SD Shield for Arduino
SKU:- Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
- Stackable Design, can directly be supported by Arduino official Ethernet Library.
- Supports up to four simultaneous socket connections
- Can be used to store files for serving over the network.
- Can be accessed using the Mini SD TF library.
- IEEE802.3af compliant
- Low output ripple and noise (100mVpp)
- Overload and short-circuit protection
SKU: n/a -
Shield for Arduino
XBee IO Expansion Shield – XBEE 2
SKU:- Expand 14 digital IO interface (12 steering gear interface)and power
- Six analog IO interfaces and power
- One digital port interface for external power supply terminals
- Digital port external power supply and on-board electrical automatic switch
- One external power input terminals and one input needle
- RS485 interface (D0-RX, D1-TX, D2-EN)
- IIC/the I2C/TWI interface (A4-SDA, A5-SCL)
- SD card module interface
SKU: n/a -
Shield for Arduino
Arduino Opta WiFi AFX00002
SKU:- Input    : 8x configurable digital / analog (0-10V) input
- Processor: STM32H747XI Dual ARM® Cortex®:
Cortex -M7 core up to 480 MHz
Cortex -M4 core up to 240 MHz - Connectivity: Support 10/100 Ethernet (TCP/IP or Modbus TCP)
USB-C
Wi-Fi + Bluetooth® Low Energy
RS485 half duplex
SKU: n/a -
-
Shield for Arduino
Arduino Leonardo with Headers A000057
SKU:- Microcontroller: ATmega32u4 with built-in USB functionality.
- Memory: 32 KB Flash, 2.5 KB SRAM, 1 KB EEPROM.
- Clock Speed: 16 MHz for efficient processing.
- Power Options: USB or external power supply.
- USB Device: Acts as a keyboard or mouse when connected to a computer.
SKU: n/a -
-
Shield for Arduino
Arduino Pro Opta Ext D1608E AFX00005
SKU:- Processor: 48 MHz Arm Cortex-M4 core
- Termination Style: Screw Terminal
- Type: Input, Output (I/O) Module
- Number of Inputs and Type: 16 – Digital
- Number of Outputs and Type: 8 – Relay
- Supply Voltage: 12 ~ 24VDC
- Operating Temperature: -20°C ~ 50°C
SKU: n/a
