Motor Drivers
Showing 49–96 of 198 results
-
Cytron Motor Drivers
Advanced Auto-Calibrating Line Sensor LSA08
SKU:- 8 sensor pairs spaced 16mm.
- 12V input power
- Onboard Mode and a Select button for instant configuration of LSA08
- LCD display unit showing 8 sensors analog value with bar chart and line position.
- Simple Auto-Calibration function to the line following surface.
- Low current consumption (typically 26mA)
- Works on glossy or reflective surface
- Refresh rate up to 200Hz.
SKU: n/a -
Brushed / Brushless DC motor Driver
Dual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A)
Brushed / Brushless DC motor DriverDual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A)
SKU:- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 19 mΩ (per leg)
- Maximum PWM frequency: 20 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
SKU: n/a -
-
Cytron Motor Drivers
Cytron 20Amp 6V-30V DC Motor Driver MD20A
SKU:- Bidirectional control for one brushed DC motor.
- Operating Voltage: DC 6V to 30V
- Maximum Motor Current: 20A continuous, 60A peak
- Buttons for quick testing.
- LEDs for motor output state.
- Overcurrent protection with active current limiting.
- Temperature protection.
- Undervoltage shutdown.
SKU: n/a -
Cytron Motor Drivers
Cytron Smart Drive Mdds30 Dual 30A (80A Peak)
SKU:- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm.
SKU: n/a -
Servo Motor Drivers
16-Channel 12-bit PWM/Servo Driver – I2C interface – PCA9685
SKU:- Operating voltage: 2.3V to 5.5V
- 5.5V tolerant inputs
- Can operate at minus 40 degrees Celsius to 85 degrees Celsius
- Software reset feature (SWRST Call) allows the device via I2C bus reset
- 25MHz internal oscillator requires no external components
- The maximum allowable 50MHz external clock input
SKU: n/a -
Stepper Motor Drivers
L9110 L9110S DC Stepper Motor Driver Board HBridge
SKU:- Â Power supply voltage: DC2.5-12V
- Â Each channel has 800mA continuous current output
- Â Low saturation pressure drop
- Â TTL/CMOS output level compatible can be connected directly to the CPU
- Â Control and drive integrated into IC
- Â Have pin high-pressure protection function
SKU: n/a -
-
-
Brushed / Brushless DC motor Driver
12V 24V 36V 40A PWM DC Motor Speed Controller Forward Reverse Adjustable Knob Switch with Case
Brushed / Brushless DC motor Driver12V 24V 36V 40A PWM DC Motor Speed Controller Forward Reverse Adjustable Knob Switch with Case
SKU:- Input voltage: DC12 to 36V (equal to the rated voltage of the motor)
- Output voltage: linear under load
- Maximum current: 50A
- Continuous current: 40A
- Support motor: DC brush motor
SKU: n/a -
Cytron Motor Drivers
Cytron Maker Reflect: Simplifying IR Reflectance Sensor for Beginner
SKU:- Operating Voltage: 3.3V and 5V Compatible
- Sensing Distance (Height): 1mm to 40mm (Vcc = 5V, Blackline on a white surface)
- Features a tiny reflectance sensor
- This sensor is used in line following robot
- Fits easily in the tightest space
SKU: n/a -
-
Cytron Motor Drivers
Cytron Maker UNO Microcontroller Board- Arduino UNO Compatible Module
SKU:- SMD ATmega328P microcontroller(the same microcontroller on Arduino UNO) with Optiboot (UNO) Bootloader
- USB Programming facilitated by the CH340
- Input voltage: USB 5V, from computer, power bank or standard USB adapter
- Piezo buzzer that will act as simple audio output
- 500mA (maximum) 3.3V voltage regulator
- 0-5V outputs with 3.3V compatible inputs
- 14 Digital I/O Pins (6 PWM outputs)
- 6 Analog Inputs
- ISP 6-pin Header
SKU: n/a -
-
Cytron Motor Drivers
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
SKU:Â
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
SKU: n/a -
-
-
Cytron Motor Drivers
Enhanced Cytron 40Amp DC Motor Driver (Peak 80amp) MDS40B
SKU:-
Bi-directional control for a single brushed DC motor.
-
Support motor from 10V to 45V.
-
Maximum current up to 80A peak, reduce to 40A gradually according to temperature.
-
16 KHz switching frequency for quiet operation.
-
NO Reverse polarity protection.
-
Protection of overvoltage.
SKU: n/a -
-
Dimension Engineering Motor Drivers
Sabertooth Dual 12A Motor Driver
SKU:- 12A continuous, 25A peak per channel Up to 24V in
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Peak Current (A): 25A
- Continuous Current (A): 12
- Operating Voltage(VDC): 18 to 24V
- No. of Channels: 2
SKU: n/a -
Brushed / Brushless DC motor Driver
SmartElex 30D Smart Motor Driver (Powered by Raspberry Pi)
SKU:- Supplying 30 amps continuously with peak currents up to 85 amps (2 Sec) per channel.
- Support motor voltage from 7V to 28V.
- Onboard Low Internal resistance MOSFETs are switched at 16KHz frequency.
- Overcurrent protection and indication.
- Thermal protection.
- Type-C USB for SERIAL Mode
SKU: n/a -
-
Cytron Motor Drivers
Cytron Maker Drive H-Bridge Motor Driver
SKU:- Dual channel, Bi-directional control motor driver
- Support motor voltage from 2.5V to 9.5VDC
- Maximum current up to 1.0A continuous and 1.5A peak (<5 seconds)
- 5V Output (200mA)Â to power the controller.
- Inputs compatible with 1.8V, 3.3V and 5V logic (Arduino, Raspberry Pi, etc).
- Solid state components provide faster response time and eliminate the wear and tear of mechanical relay
- Regenerative Braking
Â
SKU: n/a -
Stepper Motor Drivers
TL-Smoother Eight Chip Module DFORCE Vibration Pattern Filter with Cable
SKU:- TL Smoother can effectively eliminate the mechanical chatter generated by 3D printer motors,
- The TL-Smoother is an addon module for 3D printer stepper motor drivers.
- The board provides flyback diodes for the motor outputs, so they are also protected against inductance voltages in the unpowered state of the driver.
- You will get smoother movement, especially on the delta-style 3D printer
- I3 and UM models can also be used, and different machines will have different clipping effects.
SKU: n/a -
-
-
Brushed / Brushless DC motor Driver
12V 24V 36V 40A PWM DC Motor Speed Controller Forward Reverse Adjustable Knob Switch Control Driver Digital Display
Brushed / Brushless DC motor Driver12V 24V 36V 40A PWM DC Motor Speed Controller Forward Reverse Adjustable Knob Switch Control Driver Digital Display
SKU:- Input voltage: DC12 to 36V (equal to the rated voltage of the motor)
- Output voltage: linear under load
- Maximum current: 50A
- Continuous current: 40A
- Speed regulation mode: potentiometer (linear)
- Support motor: DC brush motor
SKU: n/a -
-
Cytron Motor Drivers
Cytron 25A 7V-58V DC motor driver with Switch and Potentiometer Control (MD25HV POT)
Cytron Motor DriversCytron 25A 7V-58V DC motor driver with Switch and Potentiometer Control (MD25HV POT)
SKU:- Bidirectional control for one brushed DC motor.
- Maximum Motor Current: 25A continuous, 60A peak.
- 5V output for the host controller (250mA max).
- Buttons for quick testing.
- PWM frequency up to 40kHz.
- Dual Input Mode: PWM/DIR or Potentiometer/Switch Input.
SKU: n/a -
Dimension Engineering Motor Drivers
Sabertooth Dual 25A Motor Driver
SKU:- 25A continuous, 50A peak per channel
6-30V nominal, 33.6V absolute maximum - Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Input modes: Analog, R/C, simplified serial, packetized serial
SKU: n/a - 25A continuous, 50A peak per channel
-
Stepper Motor Drivers
LV8729 6V-36V Ultra Quiet 4-layer Substrate Stepper Motor Driver with Heatsink for 3D Printer
Stepper Motor DriversLV8729 6V-36V Ultra Quiet 4-layer Substrate Stepper Motor Driver with Heatsink for 3D Printer
SKU:1. In 64 subdivision or 128 subdivision to achieve a better ultra-quiet effect.
2. Operating voltage: 6V-36V, the proposed voltage is 12V.
3. The maximum current is 1.5A, the default is 0.8A.
4. Segment: 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128.SKU: n/a -
Cytron Motor Drivers
Cytron 10Amp 7V-30V DC Motor Driver for R/C (2 Channel) MDDRC10
SKU:- Operating Voltage: DC 7 V to 30 V
- Maximum Motor Current: 10 A continuous, 30 A peak
- Motor Output PWM Frequency: 20 kHz
- RC Input Voltage (RC1 & RC2): Low Level: 0-0.7 V | High Level: 1.5-15 V
- Output Maximum Current: 0-500 mA
SKU: n/a -
Dimension Engineering Motor Drivers
Sabertooth Dual 32A Motor Driver
SKU:- 32A continuous, 64A peak per channel
- 6-30V nominal, 33.6V absolute maximum
- Synchronous regenerative drive
- Ultrasonic 30 kHz switching frequency
- Thermal and overcurrent protection
- Battery protection mode
- USB control and monitoring
- USB serial converter mode for Kangaroo x2
- Configurable current limiting
- Custom user modes
- 12-bit motor outputs
SKU: n/a -
Cytron Motor Drivers
Cytron LCD keypad Shield High Quality
SKU:- Provides a user-friendly interface that allows users to go through the menu, make selections etc.
- It consists of a 1602 white character blue backlight LCD.
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
SKU: n/a -
Cytron Motor Drivers
10A Motor Driver Shield – MD10
SKU:- Bi-directional control of 1 brushed DC motor.
- Support motor voltage ranges from 7V to 25V, .
- Maximum current up to 10A continuous and 15A peak (10 seconds).
- Solid state components provide faster response time and eliminate the wear and tear of a mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
- Speed control PWM frequency up to 10KHz.
- Selectable digital pins for PWM and DIR.
SKU: n/a -
-
Cytron Motor Drivers
Cytron Maker Line: Simplifying Line Sensor For Beginner Â
SKU:- Operating Voltage: DCÂ 3.3V and 5V compatible (With reverse polarity protection).
- Recommended Line Width: 13mm to 30mm.
- Sensor Refresh Rate: 200Hz
- Easy calibration process.
- Supports a wide range of controllers such as Arduino, Raspberry Pi, etc.
SKU: n/a -
Cytron Motor Drivers
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
SKU:-
Input Voltage (Motor): 10 – 45VDC
- Maximum current up to 100A peak (1 second), 60A continuously, each channel.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
- DC Brush motor Driver, not for brushless motor
- Dual Channels, it can drive two brush motor independently, or mixed.
- Version: Rev 1.10
SKU: n/a -
-